- Chinese Optics Letters
- Vol. 24, Issue 6, 062201 (2026)
Abstract
Keywords
1. Introduction
Augmented reality (AR) is evolving into a next-generation computing platform, yet its optical systems often face inherent trade-offs among device thickness, optical efficiency, and imaging performance. Current commercial AR glasses primarily employ geometrical or diffractive optical waveguides, which offer compact form factors but typically suffer from low optical efficiency. A decrease in optical efficiency leads directly to elevated power consumption, thereby shortening operational battery life—one of the principal impediments to the large-scale adoption of current AR glasses. Ergonomic considerations demand lightweight and compact designs to enhance user comfort and portability, thereby imposing stringent challenges on optical design, including trade-offs in performance, dynamic range, and vergence–accommodation conflict (VAC)[1].
Existing AR optical architectures mainly include reflective, diffractive, and geometrical waveguides. Reflective optical systems can achieve high image quality and wide field of view (FOV) but at the expense of increased structural complexity and system thickness, often exceeding 16 mm[2,3]. Cheng et al. designed a freeform prism-based head-mounted display that maintains high image quality and wide FOV with an optical thickness below 9.5 mm[4,5]. Diffractive waveguides can further reduce system thickness to around 1.5 mm; however, their optical efficiency typically falls below 10%, and they operate within a narrow spectral bandwidth[6,7]. Geometrical waveguides exhibit compactness with a thickness of approximately 2.3 mm and an optical efficiency of about 20%, yet their imaging uniformity is highly sensitive to mirror alignment, multilayer coating quality, and manufacturing tolerances[1,8–10]. In addition, metasurface-based approaches still encounter challenges in terms of efficiency, fabrication cost, and broadband optimization[11–15]. Overall, conventional optical designs are constrained by the coupled trade-offs among thickness, optical efficiency, and imaging performance, which make further optimization increasingly difficult.
To address these limitations, we propose a novel AR optical waveguide based on a microprism that achieves simultaneous thinness, high optical efficiency, and superior imaging quality. The microprism can be efficiently fabricated through single-point diamond turning and injection molding. During light propagation, the proposed waveguide ensures total internal reflection (TIR) for efficient light transmission, while a semi-transparent beam-splitting coating enables the simultaneous delivery of virtual and real-world images to the human eye.
Sign up for Chinese Optics Letters TOC. Get the latest issue of Chinese Optics Letters delivered right to you!Sign up now
Unlike previous optical–algorithm co-design studies that primarily focus on post-capture image processing[16,17], our method emphasizes pre-projection image preprocessing to alleviate the optical design burden and preemptively correct chromatic aberration and geometric distortion. End-to-end joint optimization between optical components and computational algorithms has been successfully applied in various fields, including extended depth of field[16,18–21], super-resolution imaging[22], aberration correction[23], and high dynamic range imaging[24]. Building on the differentiable ray-tracing framework[23], we adapt the code to AR display design by integrating a microprism waveguide model, thereby enabling a deep-learning-assisted hardware–software co-optimization platform.
Simulation results demonstrate that the proposed microprism waveguide achieves a total system thickness of only 8 mm, an optical efficiency of approximately 44.3%, a binocular FOV of 36°, and high-quality imaging performance. This approach provides a new pathway toward lightweight, energy-efficient, and high-performance AR display systems.
2. Method
As illustrated in Fig. 1(a), the microprism waveguide AR display consists of two optical paths: one dedicated to virtual image projection and the other for direct observation of real-world scenes. Figure 1(b) presents the structural composition of the system, which integrates two microprism surfaces—surface 1 and surface 4—alongside an anamorphic aspheric surface (surface 2) (Supplementary Material, Sec. S2).
![]()
Figure 1.Overall structure and optical path of the designed microprism waveguide system. (a) Optical path schematic of the microprism waveguide, illustrating the light propagation from the micro-OLED display. (b) Structural representation of the designed microprism waveguide, showing key surfaces (surfaces 1–4). (c) Detailed schematic of the microprism surface design, including layer profiles and structural parameters.
![]()
Figure 2.Optical path of rays of different object fields and different pupil positions in the microprism waveguide: the incident angles of the rays on surfaces 2′ and 1′ depend on their field and pupil positions, and they are controlled to satisfy TIR conditions.
The microprism closer to the eye facilitates the formation of virtual images, while the microprism positioned farther from the eye serves as an auxiliary element, preserving an undistorted see-through view of the external environment. As illustrated in Fig. 1(a), light emitted from a specific point on the display first undergoes refraction at surface 3, adjacent to the display, then sequentially reflects off surfaces , , and 2, and finally transmits through surface 1 to reach the exit pupil of the system. The base surface of the microprism lens and the microprism surface must satisfy the condition for TIR. Surface 2 of the prism is coated with a semi-reflective layer to enable optical see-through functionality. Light originating from the display is reflected by surface 2, while light from the real-world scene is transmitted through. The microprism waveguide AR display consists of two bonded lenses, with their bonding surfaces joined using Norland 136 adhesive. As illustrated in Fig. 1(c), the sag of the original surface is described by Eq. (1),
If the distance between and is , then the sag of the microprism surface can be expressed as
According to Snell’s law and Eq. (5), the microprism surface produces the same deflection effect on the incident rays as the original surface.
Equation (4) enables the transformation of a thick lens into a thinned structure conforming to the base surface, with a thinning ratio of , where denotes the lens aperture and is the final thickness. Fresnel lenses adopt a concentric ring-shaped microprism for focusing or collimation, while our microprism is linearly arranged to enable directional light control, better suited to AR applications. Unlike dispersion-sensitive and complex-to-manufacture metasurfaces, microprism surfaces operate across a broad spectral range, exhibit high optical transmittance, and feature microprism with thicknesses on the order of tens of microns, making them well-suited for most thinning applications. Using Eq. (4), the microprism surface can be represented with fewer parameters, facilitating a more efficient optimization process.
Throughout the optimization process, the unit direction vector of the light ray and the surface normal vector must satisfy the constraints of the TIR, as shown in Fig. 2. Here, represent the refractive indices of the media on the incident and emergent sides of the light ray, respectively. K26R is used as the injection molding material for the lenses, and the two lens bonding surfaces are bonded. The light emitted from the display first enters the waveguide, undergoes TIR at the bonded interface, and then experiences another TIR at the waveguide–air interface. Using Eq. (6), the conditions for valid light rays are determined, ensuring that only light undergoing TIR can be transmitted from the display to the human eye,
On the double bonding surface, a semi-transparent and semi-reflective coating is required for the region, where . TIR plays a crucial role in constraining the FOV of the AR display, with being limited by TIR angle of region () and being constrained by the TIR of region . The TIR angle is further influenced by the injection molding material and the bonding materials utilized in the fabrication process. With the intentional 50:50 power split introduced by the semi-reflective coating and the Fresnel losses at the microprism-related interfaces taken into account, the resulting optical efficiency is approximately 44.3%; applying anti-reflection coatings on the relevant interfaces would further suppress Fresnel reflections and increase the efficiency toward the film-limited upper bound of approximately 50% for the current splitting design. Further details, including the surface-resolved efficiency breakdown and related analysis, are given in the Supplementary Material, Sec. S8.
In pursuit of an ultralightweight design, the number of optical surfaces is significantly minimized, thereby restricting the available optimization space. To mitigate the burden of optical design, we introduce a deep-learning-based framework[25] for AR display design. The end-to-end AR display design framework integrates a deep-learning-trained neural network to preprocess images from the display, effectively reducing distortions and aberrations. This framework employs an end-to-end optimization strategy, ensuring seamless synergy between algorithmic processing and optical design, ultimately yielding an optimized microprism-based AR display system.
The end-to-end AR display design framework is based on a differentiable ray-tracing framework[25], as illustrated in Fig. 3. During the forward image simulation process, deep neural network first performs image preprocessing, after which the preprocessed image is displayed on the OLED screen and subsequently propagates through the microprism waveguide before reaching the human eye. The employed image preprocessing network and the joint optimization strategy are detailed in the Supplementary Material, Sec. S6. Throughout this process, the gradients of each optical parameter (including surface curvature, position, conic coefficients, microprism’s parameters, and polynomial coefficients) are tracked. In the backpropagation phase, the error between the target image and the perceived image is propagated backward to optimize both the microprism waveguide and the image preprocessing network,
![]()
Figure 3.End-to-end AR display design framework. A differentiable ray-tracing framework is employed to simulate the monocular eye-captured image from a given origin image. The origin image is first processed by an image preprocessing neural network and then transmitted through the microprism-based waveguide AR glasses to the human eye. During the forward simulation process (indicated by black arrows), the gradients of each optical parameter are tracked. The errors are subsequently backpropagated (orange arrows) from both the simulated image and the final network output, thereby enabling end-to-end joint optimization that integrates optical system design and image reconstruction.
The input image is first processed through a deep learning network , which maps the undistorted image across different color channels to a distortion- and aberration-compensated image. The training dataset used is DIV2K. Generalization analysis on the validation set is provided in the Supplementary Material, Sec. S7, and the training curve and convergence behavior are presented in the Supplementary Material, Sec. S6. The preprocessed image is then propagated through the microprism waveguide, where it undergoes convolution with the point spread function (PSF) of the microprism waveguide and is ultimately projected to the human eye,
3. Result
As shown in Fig. 4, the use of a neural network for pre-compensation of chromatic aberration and geometric distortion proves to be highly effective. Figure 4(a) shows the original image, in which the background railing appears straight. However, after passing through the designed microprism-based AR display, noticeable distortion and chromatic aberration are observed—most notably, lateral chromatic aberration appears along the edges of the cat’s foot [Fig. 4(b)]. Although the visual effects in Fig. 4 are slightly limited due to size constraints, the corresponding enlarged images provided in the Supplementary Material, Fig. S4, more clearly reveal the chromatic fringing and geometric distortion. The resulting image yields a peak signal-to-noise ratio (PSNR) of 11.86 dB and a structural similarity index measure (SSIM) of 0.5471, indicating significant degradation.
![]()
Figure 4.Comparison of image distortion and chromatic aberration correction induced by the microprism. (a) Ground truth image. (b) Simulation-based final display result after end-to-end compensation. (c) Output of the image preprocessing network. (d) Image directly rendered without any preprocessing. (e) Chromatic shift distribution corresponding to the black box region in (b). (f) Chromatic shift distribution corresponding to the black box region in (c).
When the original image is pre-compensated by a neural network to correct for both geometric distortion and chromatic aberration, the resulting image—after passing through the same microprism-based AR display—shows substantial improvement. As illustrated in Fig. 4(c), both types of aberrations are effectively mitigated, demonstrating the effectiveness of the pre-compensation strategy. The improvement is also more visually evident in the Supplementary Material, Fig. S4. The PSNR and SSIM of the corrected image reach 19.62 dB and 0.8438, respectively. Figure 5 presents the virtual image displayed through the microprism waveguide after joint optimization [Fig. 5(a)], as well as the MTF of the real-world scene observed through the microprism waveguide and compensating lens [Fig. 5(b)]. The MTF was evaluated at a pupil diameter of 4 mm, across representative field angles including the optical axis and edge of the FOV.
![]()
Figure 5.The initial structure of the microprism-based AR display concerning MTF for (a) virtual image display and (b) real-world scene observation.
In the Supplementary Material, we present the imaging performance of a fabricated microprism surface when applied to real-world scenes. A laser-based demonstration was conducted to visualize the light propagation within the microprism waveguide (Supplementary Material, Sec. S3).
To assess potential stray-light and ghost-image artifacts in the proposed microprism-based AR waveguide, we conducted non-sequential ray tracing over the sampled field angles and monitored the irradiance distribution on a detector placed at the eyebox plane (Supplementary Material, Fig. S9). The simulation shows that a fraction of rays is transmitted through the semi-reflective film and continues propagating inside the waveguide, while another fraction undergoes additional reflections at the microprism interfaces and forms secondary exit paths. Importantly, the resulting stray-light spot is spatially separated from the primary coupling-out region, and the corresponding secondary exit is located 20.3 mm away from the eyebox center, indicating a low likelihood of overlap with the viewing zone and, thus, a low probability of forming a visible ghost image. A residual ghost contribution could only occur if the transmitted component is reflected toward the eye by the compensation optics and re-enters the nominal eyebox; this return path is inherently weak and can be further suppressed by applying an AR coating on the rear surface of the compensation lens. Further mitigation strategies include AR coatings on microprism surfaces and locally reducing the microprism fill factor in selected regions to interrupt residual-ray propagation.
We also assessed the see-through distortion of the proposed waveguide and found only minor geometric distortion across the designed FOV, with the corresponding distortion grid provided in the Supplementary Material, Fig. S5.
| Parameter | Value |
|---|---|
| FOV (binocular) | 36° |
| Eye box (H × V) | 8 mm × 6 mm |
| MTF of virtual imaging | >0.23 at 30 lp/mm |
| Wavelength | 656.3–486.1 nm |
| Optical efficiency | ≈44.3% |
| System thickness | 8 mm |
Table 1. Performance of the System
4. Conclusion
In this work, we proposed and demonstrated a novel AR optical waveguide based on a microprism. By combining geometric optics with deep-learning-assisted optimization, the proposed system achieves a compact optical configuration that simultaneously ensures high efficiency and imaging quality. The microprism enables TIR-based light guiding with minimal thickness, while a semi-transparent beam-splitting coating allows the seamless integration of virtual and real-world imagery. Furthermore, a differentiable ray-tracing framework was incorporated to enable end-to-end joint optimization between the optical design and the image preprocessing network. This synergistic approach effectively compensates for geometric distortion and chromatic aberration, significantly enhancing visual fidelity. Simulation results confirm that the optimized system achieves a total thickness of only 8 mm, an optical efficiency of approximately 44.3%, and a binocular FOV of 36°, while maintaining high image quality and see-through performance, as summarized in Table 1. Overall, this work establishes a promising design paradigm for next-generation AR display systems by bridging optical engineering and computational optimization. The proposed microprism-based waveguide provides a lightweight, energy-efficient, and scalable solution for compact AR devices, paving the way for future integration of optical–computational co-design in wearable display technologies.
References
[21] X. Yang, M. Souza, K. Wang et al. End-to-end hybrid refractive-diffractive lens design with differentiable ray-wave model, 47(2024).
[24] Q. Sun, E. Tseng, Q. Fu et al. Learning rank-1 diffractive optics for single-shot high dynamic range imaging, 1383(2020).
Set citation alerts for the article
Please enter your email address


AI Video Guide
AI Picture Guide
AI One Sentence


